Basic properties of soil and crusher dustpecific gravity fineness modulus plasticity index ip according to table 3.2, samples considered to be the sample.49 3.18 16 sample.19 2.94 55 sample.14 2.41 59 mixed with crusher sample.13 3.03 34 crusher dust 2.55 3.34igure 3.1 particle size distribution curve.
The coarseness of sand is expressed by fineness modulus mxefined as follows 5.100. the bigger the fineness modulus is, the more coarse the sand is. the fineness modulus of the sand used in.
275. therefore, fineness modulus of aggregate cumulative retained 100 275100 2.75 fineness modulus of fine aggregate is 2.75. it means the average value of aggregate is in between thed sieve andd sieve. it means the average aggregate size is in between 0.3mm to 0.6mm as shown in below figure.
Crusher dust isommon byproduct of mining and quarrying. rather than being discarded asineness modulus 3.10 2.35 3. grading zone iiis 3831970 zone iiis 3831970 tablehysical properties of coarse aggregate s.no characteristics tested values.
The fineness modulus value gives an idea of the mean size of the particles present in the aggregates. the object of finding the fineness value is to grade the aggregate for the most economical mix for the required strength and workability with minimum quantity of cement. if the tested aggregate gives higher fineness modulus means the mix will.
The coarseness of sand is expressed by fineness modulus mxefined as follows 5.100. the bigger the fineness modulus is, the more coarse the sand is. the fineness modulus of the sand.
Fineness modulus of 10 mm aggregate 6.9 fineness modulus of 20 mm aggregate 7.7 water absorption 0.8 15050 mm were casted during this investigation. specific gravity 2.6 curing fig. 2. particle size distribution of coarse aggregate d. stone dust grey col our stone dust was collected from local.
. selection of raw materials. the parent rock used for processing artificial sand shall not have potential alkaline aggregate reactivity, and the compressive.
Fineness modulus and specific gravity of this material was 2.76 and 2.3 crusher dust isine material formed during the process of comminution of.
Stone crusher dust asine aggregate in concrete for paving crusher dust fineness modulus specific gravity of the sand used for the preparation of concrete was found to be higher than the specific gravity of crusher dust density of the. read.
Fineness modulus of coarse aggregate 2.65 2.9 specific gravity it is defined as the ratio of the mass of void iniven volume of sample to the mass of an equal volume of water at the same temperature.
D. stone dust grey col our stone dust was collected from local stone crushing units of bharatpur, rewa road, uttar pradesh. it was initially dry in condition and thoroughly retained on is 150 sieve before preparation of mix. fineness modulus and specific gravity was 2.85 and 2.4 respectively. the particle size distribution curve is shown in fig. 3. fig. 3.
Fineness modulus of crusher dust 30lp5 fineness modulus of crusher dustineness modulus for natural sandone kind of fineness modulus can be graded in many ways the fineness modulus of machine made sand can be controlled artificially by production processand the production can be organized according to users requirementswhich is impossible .
B as per the grading given in table 1, the fineness modulus of sand could vary from i.2 to 2.2. however, it is preferable to have minimum fineness modulus of l4 in case of crushed stone sands and crushed gravel sands and.f in case of naturally occurring sands. hence,.
Calculation of fineness modulus of sand. let us say the dry weight of sample 1000gm after sieve analysis the values appeared are tabulated below. therefore, fineness modulus of aggregate cumulative retained 100 275100 2.75 fineness modulus of fine aggregate is 2.75. it means the average value of aggregate is in between thed.
Fineness modulus of crusher dust, how to calculate fineness modulus of crusher dust density of sand and crusher dust stone crusher dust asine aggregate in concrete for paving crusher dustfineness modulus calculations in less thanin! plus excel, 30 dec 2018 the fineness modulus is used to describe sand gradations withingle number.
Robo sand robo sand or crusher dust obtained from local granite crushers was used in concrete to cast the cubes and cylinders. the bulk density of robo sand or crusher dust is 1768 kgm3. the specific gravity and fineness modulus of robo sand are 2.66 and 2.88 respectively. sieve analysis results are shown in fig. no. 2.
Robo sand robo sand or crusher dust obtained from local granite crushers was used in concrete to cast the cubes and cylinders the bulk density of robo sand or crusher dust is 1768 kgm3 the specific gravity and fineness modulus of robo sand are 266 and 288 respectively.
Crusher dust fineness modulus specific gravity of the sand used for the preparation of concrete was found to be higher than the specific gravity of crusher dust. density of the how many tons of quarry dust are inubic foot gold ore.
Basic properties of soil and crusher dustpecific gravity fineness modulus plasticity index ip according to table 3.2, samples considered to be the sample.49 3.18 16 sample.19 2.94 55 sample.14 2.41 59 mixed with crusher sample.13 3.03 34 crusher dust 2.55 3.34igure 3.1 particle size distribution curve.
Office Add: High-Tech Industrial Development Zone of Zhengzhou City, China
Email: [email protected]