Aggregate crushing value ba00 whereeight of ovendried sampleeight inf fraction passing through 2.36 mm is sieve. 6.video aggregate crushing value test.
Aggregate crushing value test astm pdf abrasion test is the measure of aggregate toughness and abrasion resistance such as crushing, degradation and disintegration. this test is suggested by aashto6 or astm31 resistance to degradation of smallsize coarse aggregate by abrasion and impact in los angeles machine.
The aggregate crushing value formula is given below, aggregate crushing value w3r w3 w2 w1 w1 empty weight of cylindrical measure. w2 weight of aggregate with cylindrical measure2 w1 weight of aggregate sample w3 weight of crushed aggregate sample passed through 2.36 mm is sieve.
Aggregate crushing value weight of fraction passing through the 2.36 mm sieve weight of surface dry sample w200 w1w wheres the weight of empty cylinder result the mean of the two results shall be reported to the nearest whole number as the aggregate crushing value of the size of the material tested.
Aggregate crushing value is defined as the percentage by weight of the crushed or finer material obtained when the test aggregates are subjected topecified load under standardized conditions, and the strength of the aggregate used in road construction is expressed by numerical index.
The average crushing value in the different tests is the actual crushing value of aggregate. important points to remember. it is recommended that the crushing value of aggregate should be less than 30. if it is more than 30 then 10 finer aggregate is suggested to use. the aggregate whose crushing value is less than 30 can be used for.
Aggregate crushing value 1.objective the aggregate crushing value giveselative measure of the resistance of an aggregate to crushing underradually applied compressive load. with aggregate of aggregate crushing value 30 or higher, the result may be anomalous, and in such cases the ten percent fines value should be determined instead.
Aggregate crushing value weight of fraction passing through the 2.36 mm sieve weight of surface dry sample00w wheres the weight of empty cylinder. result. the mean of the two results shall be reported to the nearest whole number as the aggregate crushing value of the size of the material tested.
Preferably the aggregate crushing value of the coarse aggregate used for cement concrete pavement at surface should not exceed 30 percent. for aggregates used for concrete other than for wearing surfaces, the aggregates crushing value shall not exceed 45 percent.
The crushing value of aggregates is measured in the ratio between the crushed aggregates, obtained from the is sieve 2.36mm and the weight of the dried aggregate sample. at least three samples should be tested from the same batch and average value to get accurate results. the crushing value of aggregate w2w100 lab report.
Aggregate crushing value test on coarse aggregates giveselative measure of the resistance of an aggregate crushing under gradually applied compressive load. coarse aggregate crushing value is the percentage by weight of the crushed material obtained when test aggregates are subjected topecified load under standardized conditions.
Aggregate crushing value 100 record. the mean of the two results is reported to the nearest whole number as the aggregate crushing value of the tested material. safety amp precautions use hand gloves while removing containers from oven after switching off the oven. to wear safety shoes amp helmet during the time of test.
Aggregate crushing value is defined as the percentage by weight of the crushed or finer material obtained when the test aggregates are subjected topecified load under standardized conditions, and the strength of the aggregate used in road construction is expressed by numerical index. aggregates with lower crushing value showower.
Crushing value test procedure. select clean and dry aggregate passing through 12.5 mm and retained on 10.0 mm sieve. weight the empty cylindrical measure. let the weight berams. fill the aggregate in the cylindrical measure in three layers, tamping each layer 25 times with the rounded end of the tamping rod.
The aggregate crushing value acv which giveselative measure of the resistance of an aggregate to crushing underradually applied compressive load. the method is applicable to aggregates passing4.0 mm test sieve and retained on0.0 mm test sieve. for other size fractions, there is another recommended method.
Aggregate crushing value 100. where, is weight of surfacedry sample is weight of fraction passing the appropriate sieve reporting of results. the mean of the two results shall be reported to the nearest whole number as the aggregate crushing value of the size of material tested.
The aggregates crushing value test should be performed as per is code 2386 part iv. first, fill the sample aggregate with onethird of the cylindrical measure in three layers. each layer should be tamped 25times freely. after filling the sample aggregate, weigh and record it as w1. now fill the aggregate in the mould along with the plunger on top.
The crushed aggregate sample which is finer than 2.36 mm is separated and expressed asercentage of the original weight taken in the mold.the percentage of weight passed through the 2.36m is sieve is known as the aggregate crushing value.. in situations, when the aggregate value is 30 or higher the result may beistake and in such cases, the ten percent fines.
Aggregate crushing value depends on the shape of agg also. angular aggregates haveower acv, than irregular or rounded aggregates.if we cutore out of the same agg say in the quarry and test for compressive strength, will giveigher mpa value. it can be considered asoncrete cylinder or ucs tested in lab. so it is hard to corelate.
Aggregate crushing value 100 100. where, is weight of surfacedry sample. is weight of fraction passing the appropriate sieve. reporting of results. the mean of the two results shall be reported to the nearest whole number as the aggregate crushing value of the size of material tested.
The aggregate crushing value giveselative measure of the resistance of an aggregate to crushing underradually applied compressive load. crushing value iseasure of the strength of the aggregate. the aggregates should therefore have.
Aggregate crushing value this test helps to determine the aggregate crushing value of coarse aggregates as per is 2386 part iv 1963. the apparatus used is cylindrical measure and plunger, compression testing machine, is sieves of sizes 12.5mm, 10mm and 2.36mm procedure to determine aggregate crushing valuehe aggregates passing through.
Aggregate crushing value isumerical index of the strength of the aggregate and it is used in construction of roads and pavements. crushing value of aggregates indicates its strength. lower crushing value is recommended for roads and pavements as it indicatesower crushed fraction under load and would giveonger service life andore economical performance.
Aggregate crushing value ba00 whereeight of ovendried sampleeight inf fraction passing through 2.36 mm is sieve. 6.video aggregate crushing value test.
Office Add: High-Tech Industrial Development Zone of Zhengzhou City, China
Email: [email protected]